WCB Split Body-manufacture,factory,supplier from China

Gate valve is a kind of cut-off valve, which is used to connect or cut off the medium in the pipeline. Gate valve's opening and closing member gate, driven by the valve stem, extend the seat to do linear lifting movement.Advantages of the gate valve.1. low fluid resistanceBecause the valve body of the gate valve internal media channel is straight, the media flow through the gate valve does not change its flow direction, so the fluid resistance is small.2.

The high-pressure pneumatic ball valve only needs to use the pneumatic actuator to rotate the air source by 90 degrees and a small rolling torque to be tightly closed. Completely equal valve body cavity provides medium with low resistance and straight-through flow path. It is generally believed that the ball valve is suitable for direct opening and closing applications, but recent developments have designed the ball valve so that it can be used for throttling and control systems.

Y-kind strainer as an fundamental high-efficiency filtration system within the purification system engineering, has performed a exquisite position within the remedy of domestic wastewater and business sewage. with various blessings in layout and alertness, it's miles now desired.

1. Butterfly valve is composed of valve body, valve seat, valve plate and valve stem, and all fittings are exposed and can be seen at a glance; Ball valve is composed of valve body, valve core (a round ball) and valve stem. The position of valve core is inside the valve body, and only part of it can be seen by naked eyes, so the sealing performance of ball valve is better than that of butterfly valve.2. Butterfly valves are relatively simple in structure, and butterfly valves with low pressure are generally used. The zui high pressure of butterfly valves can only reach 64kg.

Test valve refers to the hole and remaining elements of the circular disc and with the aid of its own weight and media stress generated motion to block the media float lower back valve.  automatic valve elegance, additionally referred to as test valve, one-way valve, backflow valve or isolation valve.  disc movement is split into lifting and swing.  elevate test valves are comparable in creation to globe valves besides for the stem that drives the disc.  the medium flows in from the inlet quit (decrease side) and flows out from the hole give up (higher aspect).  valve

Different principlesButterfly valve, also known as flap valve, is a kind of regulating valve with simple structure. It can also be used for on-off control of low-pressure pipeline media, and it mainly plays the role of cutting off and throttling. When the butterfly valve is fully opened to fully closed, it is usually less than 90. The butterfly valve and the butterfly rod have no self-locking ability. In order to position the butterfly plate, a worm gear reducer should be installed on the valve stem.

Rubber soft joints have been widely used in the industry. The installation of rubber soft joints requires different installation requirements according to different types of rubber joints. Threaded screwed rubber joints: Pay attention to the installation of screwed rubber joints. The pipe fittings are laid flat on a horizontal surface. When installing, it is necessary to screw the threaded structure into the lifting section of the pipe fittings, and then screw the other section of the pipe fittings, keeping it on the horizontal plane to prevent uneven force during the installation process.

Advantages:1. easy and quick to start and close, labor-saving, low fluid resistance, can be operated frequently2. Simple structure, small size, short structure length, small volume, light weight3. start and close torque is small, because the butterfly plate on both sides of the shaft is basically equal to the action of the medium, and the direction of the torque generated is opposite, so it is relatively labor-saving4. The material of sealing surface generally adopts rubber, plastic, so the low pressure sealing performance is good.5.

The purpose of using check valve is to avoid the backflow of medium, generally in the outlet of the pump should be installed check valve. In addition, the outlet of the compressor should also be installed check valve. In summary, in order to avoid the backflow of the medium, in the equipment, installation or pipeline should be installed check valve in general in the nominal diameter of 50mm of the horizontal pipeline are selected vertical lift check valve. Straight lift check valve in the horizontal pipeline and straight pipeline can be installed.

Check valve refers to the valve that automatically opens and closes the valve flap by relying on the flow of the medium itself to prevent the backflow of the medium, also known as check valve, one-way valve, reverse flow valve, and back pressure valve.