DIN3202 F4-manufacture,factory,supplier from China

Check valve refers to the valve that automatically opens and closes the valve flap by relying on the flow of the medium itself to prevent the backflow of the medium, also known as check valve, one-way valve, reverse flow valve, and back pressure valve.

The purpose of using check valve is to avoid the backflow of medium, generally in the outlet of the pump should be installed check valve. In addition, the outlet of the compressor should also be installed check valve. In summary, in order to avoid the backflow of the medium, in the equipment, installation or pipeline should be installed check valve in general in the nominal diameter of 50mm of the horizontal pipeline are selected vertical lift check valve. Straight lift check valve in the horizontal pipeline and straight pipeline can be installed.

Advantage 1. The opening and closing is convenient, quick, labor-saving, low in fluid resistance, and can be operated frequently.2. Simple structure, small overall size, short structural length, small volume and light weight, which is suitable for large-diameter valves.3. Mud can be transported, and the liquid accumulated at the pipe mouth is the least.4. Under low pressure, good sealing can be achieved.5. Good adjustment performance. 6. When fully opened, the effective circulation area of the valve seat channel is large, and the fluid resistance is small.7.

The filter net adopts stainless steel double-layer net structure, which is durable, advanced in structure, small in flow resistance, convenient in sewage discharge, etc. It can be used in water, steam, oil, nitric acid, urea, oxidizing medium and other media. According to the user's needs, the mesh number of filter screen should be set, generally, the water supply network is 18-30 mesh, the ventilation network is 40-100 mesh, and the oil supply network is 100-480 mesh.

The check valve opening and closing parts are opened or closed by themselves by the flow and force of the medium to prevent the backflow of the medium. The valve is called a check valve. The check valve belongs to the automatic valve category, which is mainly used in the pipeline where the medium flows in one direction, and only allows the medium to flow in one direction to prevent accidents. The check valve, also known as a one-way valve or a check valve, is used to prevent the backflow of the medium in the pipeline.

Rubber soft joints have been widely used in the industry. The installation of rubber soft joints requires different installation requirements according to different types of rubber joints. Threaded screwed rubber joints: Pay attention to the installation of screwed rubber joints. The pipe fittings are laid flat on a horizontal surface. When installing, it is necessary to screw the threaded structure into the lifting section of the pipe fittings, and then screw the other section of the pipe fittings, keeping it on the horizontal plane to prevent uneven force during the installation process.

Y-kind strainer as an fundamental high-efficiency filtration system within the purification system engineering, has performed a exquisite position within the remedy of domestic wastewater and business sewage. with various blessings in layout and alertness, it's miles now desired.

1. Handwheel, handle and transmission mechanism are not allowed to be used for lifting, and collision is forbidden. 2. The double gate valve should be installed vertically (i.e. the valve stem is in the vertical position and the handwheel is at the top). 3. The gate valve with bypass valve should be opened before opening (to balance the pressure difference between inlet and outlet and reduce the opening force). 4. Gate valve with transmission mechanism shall be installed according to the product instruction manual. 5.

The high-pressure pneumatic ball valve only needs to use the pneumatic actuator to rotate the air source by 90 degrees and a small rolling torque to be tightly closed. Completely equal valve body cavity provides medium with low resistance and straight-through flow path. It is generally believed that the ball valve is suitable for direct opening and closing applications, but recent developments have designed the ball valve so that it can be used for throttling and control systems.

Different principlesButterfly valve, also known as flap valve, is a kind of regulating valve with simple structure. It can also be used for on-off control of low-pressure pipeline media, and it mainly plays the role of cutting off and throttling. When the butterfly valve is fully opened to fully closed, it is usually less than 90. The butterfly valve and the butterfly rod have no self-locking ability. In order to position the butterfly plate, a worm gear reducer should be installed on the valve stem.