CF8 Disc-manufacture,factory,supplier from China

(Total 10 Products for CF8 Disc)

CF8M DISC CF8 DISC CF3M DISC

Technical Parameters:SizeDN32-DN600DN650-DN2000Working pressure16Bar10BarShell24Bar15BarSeal(Air)6Bar6BarOperating Temperature-40℃~+160℃Operating EnvironmentBallast and bilge system Chemical processingDesalination plants Drilling rigs Drinking waterDry powder Food and beverage Gas plantsHAVC Mining industry Paper industry Sand handling Seawater Su

Contact Now

Wafer Type Dual Check Valve stainless steel body

One Board Wafer Type Check Valve CF8 Disc

At the contrary, the valve is closed while the medium flows back. swing test valves have a disc this is tilted and rotates on its axis and paintings in a similar way to lift test valves. check valves are often used as bottom valves in pumping units to save you the backflow of water. check valves are combined with globe valves to provide safety isolation. risks are large resistance, poor sealing when final.Cast Iron Wafer Type Check Valve Material:The body materia: GG25,GGG40,GGG50The disc material: DI/SS304/SS316/AL-BZThe stem/spring material: SS416/SS304The seat m

Contact Now

API6D Short Pattern Single Disc Wafer Check Valve

Material:The body materia: GG25,GGG40,GGG50The disc material: DI/SS304/SS316/AL-BZThe stem/spring material: SS416/SS304The seat material:NBR/EPDM/VITON Standard：ANSI/JIS/DIN/BS Usage：They are used for pipe of transporting water with such medium as water sewage and seawater.It can avoid media flowing backwards and prevent damaging water hammer,guarantee the safety using of pipes.Features:1. The products are new structure .small and light weight2. Reliable sealed,endurable open-close,erar-resisting,long life.3. With less flowing resistance than old check valve and obviou

Contact Now

Stainless Steel CF8 CF8M CF3M Butterfly Valve Body

Contact Now

Double Door Check Valve

Check valve is to rely on the flow of the medium itself and automatically open and close valve disc, used to prevent the media flow back valve, also known as check valve, one-way valve, countercurrent valve, and back pressure valve. Check valve is a kind of automatic valve, its main function is to prevent media backflow, prevent pump and drive motor reverse, as well as the discharge of container medium. Check valves can also be used to supply lines in which pressure may rise to exceed system pressure in the auxiliary system.

Contact Now

DI+EPDM Coated Disc Grooved End Butterfly Valve with handlever

It is easily installed with two grooved end couplings.

Contact Now

Dual Disc Check Valve 30INCH

Contact Now

Slient Check valve Wafer type

Check valve refers to the hole and ultimate additives of the spherical disc and through its very own weight and media pressure generated movement to dam the media drift lower back valve. automatic valve beauty, also known as take a look at valve, one-manner valve, backflow valve or isolation valve. disc movement is split into lifting and swing. lift check valves are similar in creation to globe valves besides for the stem that drives the disc. the medium flows in from the inlet prevent (decrease facet) and flows out from the opening quit (better side).Cast Iron Wafer Ty

Contact Now

Electric Butterfly Valve wafer type SS316 disc

electric butterfly valve can transport mud, at the mouth of the least liquid accumulation. electric butterfly valve under low pressure, can achieve good sealing.

Contact Now

PTFE Seat PTFE Coated Disc Butterfly Valve

Technical Parameters:SizeDN50-DN600Working pressure10BarShell15BarSeal(Air)11BarOperating Temperature-20℃~+180℃Operating EnvironmentBallast and bilge system Chemical processingDesalination plants Drilling rigs Drinking waterDry powder Food and beverage Gas plantsHAVC Mining industry Paper industry Sand handling Seawater Sugar industryThermo technical water treatment Waste wate

Contact Now

Relate News

The development trend of electric butterfly valve

Electric butterfly valve means that the butterfly valve is equipped with an electric actuator, which controls the opening and closing of the valve through the electric energy provided by the power supply, so as to realize remote centralized control and automatic operation. Electric butterfly valve can be divided into flange type and disc type according to the connection method, which is an important execution unit in the field of industrial automation control.

What Is The Advantage for Butterfly Valve

Butterfly Valve is a simple structure control valve,it can be used for switching control of low pressure pipeline medium. Our Butterfly Valve is a kind of valve that the disc rotate around the valve shafts to open and close. Features:1, opening and closing convenient and rapid, labor saving, fluid resistance is small, can often operate.2, simple structure, small size, short structure length, small volume, light weight, suitable for large diameter valve.3, can transport mud, the least liquid in the pipe mouth.4.

Introduction of Slient Check Valve Wafer Type

Test valve refers to the hole and remaining elements of the circular disc and with the aid of its own weight and media stress generated motion to block the media float lower back valve. automatic valve elegance, additionally referred to as test valve, one-way valve, backflow valve or isolation valve. disc movement is split into lifting and swing. elevate test valves are comparable in creation to globe valves besides for the stem that drives the disc. the medium flows in from the inlet quit (decrease side) and flows out from the hole give up (higher aspect). valve

Background of Butterfly Valve

Butterfly valve is a type of valve that uses a spherical butterfly plate as the opening and last component and turns with the valve stem to open, close and alter the fluid channel. the butterfly plate of the butterfly valve is set up in the diameter route of the pipe. in the cylindrical channel of the butterfly valve frame, the disc formed butterfly plate rotates around the axis of the valve stem at an perspective among 0 ° and 0 °. whilst the butterfly plate is at 0 °, the valve is closed, and when the butterfly plate is at ninety °, the valve is absolutely opened.

Matters Needing Attention in the Use of Gate Valves

1. Handwheel, handle and transmission mechanism are not allowed to be used for lifting, and collision is forbidden. 2. The double gate valve should be installed vertically (i.e. the valve stem is in the vertical position and the handwheel is at the top). 3. The gate valve with bypass valve should be opened before opening (to balance the pressure difference between inlet and outlet and reduce the opening force). 4. Gate valve with transmission mechanism shall be installed according to the product instruction manual. 5.

Advantages and Disadvantages of Butterfly Valve

Advantage 1. The opening and closing is convenient, quick, labor-saving, low in fluid resistance, and can be operated frequently.2. Simple structure, small overall size, short structural length, small volume and light weight, which is suitable for large-diameter valves.3. Mud can be transported, and the liquid accumulated at the pipe mouth is the least.4. Under low pressure, good sealing can be achieved.5. Good adjustment performance. 6. When fully opened, the effective circulation area of the valve seat channel is large, and the fluid resistance is small.7.

Features of electric ball valve

The high-pressure pneumatic ball valve only needs to use the pneumatic actuator to rotate the air source by 90 degrees and a small rolling torque to be tightly closed. Completely equal valve body cavity provides medium with low resistance and straight-through flow path. It is generally believed that the ball valve is suitable for direct opening and closing applications, but recent developments have designed the ball valve so that it can be used for throttling and control systems.

Common Check Valve Materials

Check valve is a valve installed in the pipeline to prevent the backflow of media. Check valves can be used on many types of pipelines such as over water, oil and gas, etc.

Check Valve Applications

The purpose of using check valve is to avoid the backflow of medium, generally in the outlet of the pump should be installed check valve. In addition, the outlet of the compressor should also be installed check valve. In summary, in order to avoid the backflow of the medium, in the equipment, installation or pipeline should be installed check valve in general in the nominal diameter of 50mm of the horizontal pipeline are selected vertical lift check valve. Straight lift check valve in the horizontal pipeline and straight pipeline can be installed.

Pressure test method of check valve

Check valve refers to the valve that automatically opens and closes the valve flap by relying on the flow of the medium itself to prevent the backflow of the medium, also known as check valve, one-way valve, reverse flow valve, and back pressure valve.